MAX3421EETJ+T fiche technique, prix | pdf

Find the comprehensive MAX3421EETJ+T Reference Manual in pdf format. Explore detailed information, features, and pricing to effectively utilize this component in your projects.

Marques : Analog Devices Inc./Maxim Integrated

Télécharger: MAX3421EETJ+T Datasheet PDF

Prix: enquête

En stock: 5,937

Protocole: USB

Fonction: Contrôleur

Interface: SPI

Emballer: 32-WFQFN Pad exposé

Livraison GRATUITE pour les commandes supérieures à HK$250.00

Réponse rapide, devis rapide

Expédition rapide, pas de soucis après-vente

Chaîne originale, garantie de produits authentiques

MAX3421EETJ Pinout Equivalent Circuit

max3421eetj pinout 1
MAX3421EETJ is a USB peripheral/host controller launched by Analog Devices, which adopts VQFN-32-EP (5×5), integrates USB transmitter and SIE (Serial Interface Engine), communicates with the host controller through SPI interface, complies with USB2.0 specification, and supports full speed 12Mbps peripheral mode and full/low-speed 12Mbps/1.5Mbps host mode. The chip also integrates a level converter, which can operate at voltages ranging from 1.4V to 3.6V. It is often used in embedded systems, instruments, medical devices, and other applications that require USB communication.

Pin definition:

PIN	Nom	FUNCTION
1	GPIN7	Input pin, provide pull-up resistor connected to VL.
2	VL	The voltage input pin for level conversion is connected to a voltage source ranging from 1.4V to 3.6V.
3, 19	GND	Grounding pin.
4~11	GOUT0~GOUT7	Universal push-pull output, logic level reference VL voltage.
12	RES	Reset pin low level is effective, clearing internal register parameters.
13	SCLK	SPI clock input (up to 26MHz), rising edge input data, falling edge output data.
14	SS	SPI chip selection input, low level effective.
15	MISO	SPI data output (main input and output), push-pull output.
16	MOSI	SPI data input (master output slave input) or bidirectional mode.
17	GPX	Programmable multiplexed output, signal type can be configured through PINCTL register.
18	INT	Interrupt output, edge mode is push-pull, level mode is open drain low effective.
20	D-	USB D-signal requires a 33 Ω resistor in series, with an internal 15k Ω pull-down resistor.
21	D+	The USB D+ signal requires a 33 Ω resistor to be connected in series, which includes a 1.5k Ω pull-up resistor and a 15k Ω pull-down resistor.
22	VBCOMP	VBUS comparator input, used to detect power status.
23	VCC	The power input is generally 3.3V.
24	XI	Connect the input pins of the crystal oscillator.
25	XO	Connect the output pins of the crystal oscillator.
26~32	GPIN0~GPIN66	Universal input pins.

Alternative model selection:

When choosing an alternative model for MAX3421EETJ, the following key aspects need to be considered to ensure that the new device can meet the original design requirements and achieve a perfect replacement as much as possible. The consistency of functionality is the most important, and it needs to be confirmed whether the replacement chip can achieve USB host/peripheral control like MAX3421EETJ, supporting the same USB protocol and data transfer rate. The second is the interface type, ensuring that the new device provides interfaces compatible with the existing system, such as SPI, I ² C, or UART, which can facilitate communication with the main controller. The third is the packaging form. If you do not want to change the original PCB shape and design, you need to determine whether the substitute chip model can be consistent with the existing one.

Nom	Interface Type	Support Agreement	Working Voltage	Emballer
MAX3421E	SPI	USB 2.0 Host/Peripheral	3.0V-3.6V	TQFP-32
MAX3420E	SPI	USB 2.0 (full speed working mode)	3.0V-3.6V	TQFP-32
VNC1L	UART/SPI	USB 2.0 Host/Peripheral	3 V ~ 3,6 V	LQFP-48
VNC2	UART/SPI	USB 2.0 Host/Peripheral	1.8V/3.3V	LQFP-48/QFN-64

Typical Applications:

Design application circuit diagram 1

Design application circuit diagram

The design in the diagram is mainly divided into four modules. Power circuit design, USB interface design, clock circuit design, and microcontroller SPI interface design.

The power circuit design mainly includes a MAX6349TL low dropout regulator that converts the 5V input from the USB port to 3.3V, providing power for the microcontroller and MAX3421EETJ.

The USB interface circuit is connected to the D+and D – pins of MAX3421EETJ through a 33 ohm resistor. When drawing the PCB later, attention should be paid to impedance matching and differential wiring. It also provides a voltage detection system that monitors the voltage provided by the USB port in real-time, serving to protect the circuit.