1N4733A ツェナーダイオード | 5.1V 1W | データシート & SPICEモデル Rectron USA

1N4733A

1N4733A

The 1N4733A zener diode is a classic, reliable choice if you need a stable 5.1V reference or voltage clamp in your circuit. It handles around 1 watt, perfect for typical protection or reference tasks. Packaged in a common glass DO-41 case, it’s known for low temperature drift and stable performance, making it great as a reference source. Plus, it reacts quickly, ideal for protecting MCU I/O pins or handling voltage surges. You’ll find it everywhere—from power supply circuits and voltage references to analog voltage clamping. It’s one of those go-to parts you’ll use again and again.

1N4733A Pinout Polarity

When you’re using the 1N4733A Zener diode, remember it’s reverse-connected—the side with the silver or black band (the cathode) goes to the positive side of your circuit, and the other end (anode) connects to negative or ground. Once the voltage rises above 5.1V, it conducts and clamps the voltage, protecting your components. Always add a resistor in series to limit current and avoid burning it out. If you’re protecting MCU pins or analog inputs, connect it parallel between the signal and ground, with the cathode facing the signal. It’s got a handy DO-41 package, easy for breadboarding or through-hole soldering.

1N4733A Equivalent Zener Diode

1N4733A Voltage Regulator Circuit

You can quickly grasp how this circuit works—it’s straightforward. On the left, you’ve got a 25V DC supply feeding through a 330Ω resistor to limit current, so your 1N4733A Zener diode doesn’t burn out. The Zener is connected in reverse, and once voltage goes above 5.1V, it clamps the output, keeping it steady right around 5.1V. Then, your load (like this 1kΩ resistor) gets a stable voltage—perfect for powering low-power circuits, sensors, or reference voltage setups. It’s a classic design you’ll find useful in many projects needing a simple and reliable regulated voltage.

1N4733A Reverse Voltage Protection

You can use a 1N4733A as a simple reverse voltage protection diode, but remember it’s actually a 5.1V Zener diode—not designed for heavy current scenarios. Normally, it won’t conduct, but if you accidentally reverse the power connection, the diode immediately clamps the voltage, redirecting current safely through a resistor to ground. It’s perfect for low-voltage logic signals or ADC inputs, like protecting a 6V system. But since it’s only rated at 1W, don’t rely on it for high-power reverse polarity protection. For bigger currents, stick with proper Schottky or rectifier diodes.

1N4733A Voltage Clamp Wiring

Using a 1N4733A diode for voltage clamping is straightforward. Just connect the diode’s cathode towards your input signal and its anode to ground, adding a resistor (330Ω–1kΩ) in series to limit current. Under 5.1V, it does nothing; above 5.1V, it clamps voltage to protect your MCU, ADC, op-amp, or logic circuits. For bidirectional signals, put two diodes facing opposite directions. Just keep in mind, its max rating is 1 watt—don’t use it for large currents. For high-frequency signals, adding a small capacitor (around 100pF) across the diode helps smooth out voltage spikes.

1N4733A Power Supply Stabilization

If you want an easy and cost-effective way to get a steady 5.1V output, using a 1N4733A Zener diode with a resistor (around 330Ω) is your simplest choice. Once your input exceeds 5.1V, it clamps the voltage neatly at that level—perfect for powering small sensors or simple circuits. Always include the resistor, though, or the diode will burn out fast. Just remember, this method only handles small currents (20–50mA). If you need higher current or better stability, you’re better off going with a dedicated regulator like the LM7805.